Ningbo Cimi Sports Co., Ltd.

SURF TRACTION TAIL PADS

SURF TRACTION TAIL PADS

For buyers looking for a wholesale surfboard pad, this peel-and-stick tail pad comes from a surfboard pad manufacturer that has built surf hardware since 2007. It sits on the tail of the surfboard deck where the back foot lands and wax wears through first, with raised grip blocks, perforated holes, and horizontal slots for back-foot control.

SURF TRACTION TAIL PADS
SURF TRACTION TAIL PADS, No.00551

Tail Pad Overview

SURF TRACTION TAIL PADS is listed as No.00551, a black speckled tail pad designed as a peel-and-stick part rather than a kit. The pad is primarily bought as a replacement part, and because it covers the tail rather than the full deck, the front half of the board stays free for wax.

The surface uses raised grip blocks, a perforated pattern, horizontal slots, and a contoured outline that follows the tail curve while keeping the pad flat at the corners. The cushioned underfoot feel takes the sting out of a hard landing without making the tail feel soft or vague. A speckled black surface uses light flecks to hide wax smear and sand, and the same pad can be standardised across a rental or school set so every board feels the same.

The product sits within a range that runs from tail pads through centre pads to waxless decks, with matching leash and fin options also mentioned in the product details.

Grip and Deck Feel

The tail pad is built around the part of the deck where the back foot works hardest, so the surface details are there to support control without adding unnecessary bulk.

Raised grip blocks

The surface stands up in small moulded blocks rather than lying flat, so the ball of the back foot bites in when driving through a turn.

Perforated holes

The pierced pattern lets water and air move across the deck instead of trapping a film under the foot, and it gives wax somewhere to settle.

Horizontal slots

These run across the pad and act as a brace, stopping the back foot from slipping off the tail.

Contoured outline

The pad is cut to follow the tail curve, keeping the pad flat at the corners.

Cushioned underfoot feel

There is enough give to take the sting out of a hard landing without making the tail feel soft or vague.

Speckled black surface

Light flecks help hide wax smear and sand on the black surface.

Consistent across a fleet

The same pad can be standardised across a rental or school set so every board feels the same.

Specifications

The product page lists the following details for No.00551.

Product number No.00551
Colour Black with light speckles (black speckled surface)
Type Tail pad / surf traction pad; peel-and-stick, not a kit
Brand CIMI; building surf hardware since 2007

The product page does not state dimensions, thickness, weight, material composition, or size variants. Confirm those details directly before ordering if they are required for your board program.

Where the Tail Pad Fits

This is a tail pad rather than a full-deck grip. It is positioned on the tail of the surfboard deck where the back foot lands and where wax wears through first.

  • Tail deck placement: supports the area where the back foot lands and the ball of the foot drives through a turn.
  • Replacement use: supplied as a straightforward peel-and-stick pad rather than a kit, and primarily bought as a replacement part.
  • Wax-friendly deck: because it is a tail pad, not full-deck grip, the front half of the board stays free for wax.
  • Fleet consistency: the same pad can be standardised across a rental or school set so every board feels the same.
  • Matching range: leash, fins, other tail pads, centre pads, skimboard pads, and waxless decks are mentioned in the product details.

Choosing This Pad

This is a tail pad rather than a full-deck grip, and it is supplied as a straightforward peel-and-stick pad rather than a kit. That makes it a practical choice when the rear foot area needs a fresh grip surface and the rest of the deck is being kept for wax. Because the pad is cut to leave the leash plug clear, it can be matched with a leash without re-drilling.

For rental or school use, the same pad can be standardised across a fleet so every board feels the same. For board builders and buyers comparing options, the wider traction range includes other tail pads, centre pads, skimboard pads, and waxless decks. Honeycomb fins in single tab and double tab fitments are also mentioned as part of the matching range.

If dimensions, thickness, weight, material composition, or size variants are required, confirm them directly because the product page does not state them.

Fitting and Care

Fitting steps

  1. Strip old grip back to bare deck; remove wax, adhesive and residue; wipe dry.
  2. Dry-fit before removing the backing; square to the stringer and hard against the tail; keep the leash plug completely clear.
  3. Mark the outline with two strips of tape as a guide.
  4. Bring the board and pad to room temperature before fitting.
  5. Peel a few centimetres of backing, anchor the tail end first, and work forward pressing centre-out.
  6. Press the whole surface firmly and seal the edges with a thumb.
  7. Leave the board flat before returning to water; check the edges after the first few sessions.

Care and longevity

  • Rinse with fresh water after a session; dry out of direct sunlight.
  • Remove wax with warm water and a soft cloth or brush rather than scraping hard; avoid solvents and aggressive cleaners.
  • Rinse or brush out sand and grit trapped in the holes and slots.
  • Check the outline every few weeks for corner lifting.
  • Store on a rack or lay flat rather than leaning tail-down against a wall.

Before You Order

Use the product page and a direct inquiry to confirm the exact item before ordering. The listed product number is No.00551, the colour is black with light speckles, and the type is a tail pad / surf traction pad supplied as a peel-and-stick pad, not a kit.

  • Confirm the product number and colour match the board program.
  • Confirm the pad will be fitted square to the stringer, hard against the tail, and fully clear of the leash plug.
  • Confirm whether the front half of the deck will remain free for wax, as intended for a tail pad rather than full-deck grip.
  • Confirm any dimensions, thickness, weight, material composition, or size variants directly, because those details are not stated on the product page.
  • For fleet use, confirm that the same pad can be standardised across the rental or school set.
  • For matching accessories, review the leash, fin, centre pad, skimboard pad, and waxless deck options in the range.

Request Product Details

For wholesale inquiries, product questions, or fitting confirmation, contact CIMI directly. Review the product page for the No.00551 tail pad before sending your requirements.

Related Reading

Three notes to help clarify product requirements before contacting the supplier.

How Do Arch Bars and Kick Tails Affect Tail Pad Control?

Arch bars and kick tails shape how a back foot sits, presses, and drives through a turn, so understanding their mechanics makes tail pad comparison far more useful.

Read article

Surfboard Tail Pads Support Back Foot Control

A tail pad sits exactly where a surfer loads weight to turn, so understanding that rear-foot position explains why the category exists at all.

Read article

Custom Logo Tail Pad Manufacturing for Private-Label Surf Brands

A custom logo tail pad becomes easier to approve when the surf brand defines artwork, texture, outline, commercial timing, and design ownership before the first sample is made.

Read article

Frequently Asked Questions

What is the product number for this tail pad?

The product number is no.00551.

What colour is the pad?

The pad is black with light speckles on a black speckled surface.

Is this a full-deck grip or a tail pad?

It is a tail pad or surf traction pad. it is supplied as a peel-and-stick pad rather than a kit, and it is primarily bought as a replacement part. because it covers the tail rather than the full deck, the front half of the board stays free for wax.

Does the product page state dimensions, thickness, weight, material composition, or size variants?

No. the product page does not state dimensions, thickness, weight, material composition, or size variants. confirm those details directly before ordering if they are required.

How should the pad be fitted?

Strip old grip to bare deck, remove wax, adhesive, and residue, and wipe dry. dry-fit before removing the backing, square to the stringer and hard against the tail, and keep the leash plug completely clear. mark the outline, bring the board and pad to room temperature, peel a few centimetres of backing, anchor the tail end first, work forward pressing centre-out, press the whole surface firmly, seal the edges, and leave the board flat before returning it to water.

How should the pad be cared for?

Rinse with fresh water after a session and dry out of direct sunlight. remove wax with warm water and a soft cloth or brush rather than scraping hard, and avoid solvents and aggressive cleaners. rinse or brush out sand and grit trapped in the holes and slots, check the outline every few weeks for corner lifting, and store the board on a rack or lay it flat rather than leaning it tail-down against a wall.

ARE YOU READY TO WORK WITH US?

Contact US