Product Overview
Hexa Traction is a full-deck surfboard traction pad built from thin hexagonal pieces. Instead of covering only the tail, the set is laid across the standing area, so the deck feels the same under the front foot as under the back — the difference you notice on a longboard traction pad, where the rider walks the deck rather than planting in one spot. The pads are clear, textured and low in profile, and they come from the waxless side of our range: nothing to melt, scrape or re-apply before a session. Shops, distributors, rental operators and surf board manufacturers buy it as the full-deck option that sits alongside the tail pads.
Key Features
- Grip across the whole stance — the dimpled hexagonal surface works as a surf traction pad across the full deck, not just under the back foot, so the front foot finds traction wherever it lands after a turn.
- Waxless by design — nothing to melt, scrape off or re-apply, and nothing to soften into the deck on a hot day; the board is ready as soon as it is dry.
- Clear finish — the pads are clear, so tint, laminate and artwork still read through the grip instead of vanishing under a solid block of colour.
- Thin and light — a flat profile keeps the board's feel and rail-to-rail response, with no thick edge for a toe or heel to roll over.
- Peel-and-stick adhesive — the backing goes straight onto a clean, dry deck, which makes it a one-visit job in a shop or a quick refit at home.
- Waterproof surface — the textured top sheds water rather than soaking it, so a paddle board traction pad keeps its grip from the first stroke of a session to the last.
- UV protection — the finish is UV protected, which counts for boards that spend their life on a roof rack, a beach rack or a shop display.
- Comes off cleanly — when the grip is worn or a deck is being refinished, the pads lift away and the deck can be cleaned back for a new set without residue left behind.
Fitting & Installation
- Strip the old grip and wax. Work the old pad off the deck, scrape the wax back to clean glass or laminate, then wipe the area with fresh water and let it dry completely — adhesive will not hold over dust, oil or moisture.
- Dry-fit the whole layout first. Lay the hexagons along the deck and check the spacing before anything is peeled; a traction pad for surfboard decks is only as good as the layout underneath it.
- Work from the centre line. Measure from the stringer so the pattern runs straight, then mark the area you are covering with pencil dots or strips of tape.
- Seat the first pad. Press it down from the centre outward with the heel of your hand, pushing trapped air toward the edges as you go.
- Build outward from that first piece. Every pad you place gives the next one an alignment edge, so the hexagons lock together across the deck.
- Re-press every edge. Run a thumb firmly along the outside edges and around any cut-outs — edges are always the first part to lift.
- Let it settle before the board goes back in the water. Fit in dry, mild conditions and give the adhesive time to settle before the first session.
Boards & Applications
- Shortboards and fish — run a section forward of the tail pad as a surfboard front traction pad, so the front foot lands on grip rather than bare laminate after a big turn.
- Paddle boards and SUPs — a paddle board traction pad across the standing zone keeps grip under a wider, flatter stance when the deck is wet and the rider is shifting weight to paddle.
- Foil decks — foil riders move their feet constantly between positions; full-deck coverage keeps every one of those positions planted instead of hunting for a dry patch.
- Rental fleets and surf schools — one consistent grip surface across a whole rack of boards, and a surfboard grip pad that can be replaced in minutes when a deck goes smooth.
- Shop refits — when a customer's old pad has lifted or flattened, a hex set brings the deck back without a full re-glass or a wax rebuild.
- Deck-grip assortments — the full-deck option that sits beside the tail pads, which is what chain buyers and surf board manufacturers ask for when a longboard traction pad, the tail pads and the rest of the deck-grip section have to be covered in one order.
Specifications
| Model | T00443 |
|---|
| Product type | Full-deck surfboard traction pad |
| Pattern | Hexagonal (Hexa Traction) |
| Pad form | Thin, flat hexagonal pieces |
| Surface | Dimpled, textured grip |
| Finish | Clear |
| Backing | Self-adhesive, peel-and-stick |
| Deck coverage | Full deck, or a large front and centre section |
| Application | Traction pad for surfboard decks, longboards, paddle boards and foil boards |
| Pack | Printed presentation box with feature panel |
| Design origin | Barcelona |
Product Presentation & Reorder
The grip ships in a printed presentation box with a feature panel on the front, so it can go straight onto a pegboard or a shelf rather than being repacked in store — useful when a chain lists a whole accessory section at once. The hexagonal pattern is a merchandising advantage in its own right: a surfboard front traction pad looks clearly different from a tail pad, so the two can sit side by side without competing for the same sale. Display it with the box at one end of the shelf and an installed deck shot at the other, and buyers see the difference between a tail pad and a full-deck grip immediately.
Companion Accessories
| Accessory family | What we supply |
| Leashes | Regular and Hypalon leashes from 6 ft to 9 ft, plus SUP and bodyboard leashes — a surfboard leash in the length that matches the board |
| Fins | Honeycomb, timber, G10 glass and nylon fins in single tab and double tab, so a board can be finished with the fin set the rider wants |
| Traction | Tail pads, centre pads, skimboard pads and waxless pads — the rest of the deck-grip range this grip belongs to |
| Covers | Basic bags, regular bags, stretch covers and bodyboard bags for transport and storage |
| Racks | Travel racks and tie-downs, storage racks, display racks and bike racks for shops, fleets and riders |
| Wax and deck care | Wax, wax inserts and the small items that go with fitting and maintaining a deck |
Ordering & Delivery
- Tell us the deck you are gripping. Board types, the area to be covered, and whether this is a single traction pad for surfboard repair or a full production run all change what we quote. 2. Agree the pattern and finish. Ask your sales contact about sample availability if you want to see the hexagonal surface and the clear finish close up before committing to a quantity. 3. Confirm the colourways and packing. Colourways, box labelling and market-specific requirements are agreed per programme rather than assumed. 4. Confirm quantities, lead time, payment terms and delivery arrangements with your sales contact — these are set per order and per destination. 5. 6.
Scale & Supply Capability
CIMI is a factory-based supplier with 16 years in surf and watersports hardgoods, manufacturing at our own facility rather than sourcing through traders. Chain stores, supermarkets and surf-brand stores buy from us because one supplier covers a full accessory assortment, so a season's order and its reorders can be planned together. We take on OEM and private-label work, adapting designs, colourways and branding to your programme, and we schedule production against your agreed range plan. Send us your buy list and target dates, and we will confirm what we can make and when.
FAQ
How does Hexa Traction differ from the tail pads in the same range?
A tail pad is shaped for the back foot and sits over the tail. This surfboard traction pad covers the standing area in hexagonal pieces, so grip is there wherever the feet land. Plenty of riders and shops run both: the tail pad at the back for turns, hex pieces forward for the rest of the deck.
Does the clear finish let the board show through?
Yes. The pads are clear, so tint, laminate and artwork stay visible underneath, which is why they work well on a longboard traction pad where the deck is part of the look. The surface is still textured — clear refers to the material, not to a smooth top.
How do I keep the grip clean?
Rinse with fresh water after salt-water sessions and let it dry before the board goes into a bag. For a build-up of sunscreen or wax film, use a little mild soap and a soft brush, then rinse again. Sand works into the dimples on any deck grip, and on a paddle board traction pad it is usually the first thing to rinse out. Keep solvents and hot wax away from a surfboard grip pad; neither does the surface any good.
Can the pads be removed later?
The surf traction pad peels away when it is worn or the deck is being refinished. Warm the pad slightly and lift it slowly from one corner rather than tearing it off, then clean the deck back before fitting a new set. The packaging lists no residue, so the deck can be brought back to a clean surface for the next grip.
Can the hexagons be trimmed to follow a narrow nose or a curved outline?
The pads are thin and flat, so a sharp blade trims them cleanly along a straight edge or around a curve — useful when a surfboard front traction pad has to follow a pulled-in nose or stop short of a deck fitting. For production runs where you need a repeated cut shape, tell us the outline and we will confirm what can be made.