L00337 SUP LEASH 10FT 8MM ANKLE

Product Overview

The 10 ft 8 mm ankle leash is the middle size in CIMI's SUP ankle range: longer than the 8 ft model for compact boards, shorter than the 12 ft version for long touring shapes, and the length most all-round paddlers settle on. There is enough reach that the board does not snap back against your heel in chop, and not so much cord that it trails through the water behind you on a flat-water session.

We build it as a sup leash manufacturer rather than a trading house, so the cuff, cord and hardware carry across the range and stay the same from one order to the next.

The cord is 8 mm rather than the 7 mm used on the surf leashes in the same programme. That extra diameter is there for the loads a stand-up board creates — more surface catching wind, more mass when a rail digs in and the water takes the board. It still has to stretch and recover, so the cord is a TPU extrusion rather than a stiff rope, and the swivels at each end take the twist out before it reaches your ankle.

At the board end there is a rail saver and a leash string; at the body end, a padded ankle cuff with a hook-and-loop strap. The cuff closes low on the ankle, which keeps it clear of the deck when you kneel to paddle through shallow water.

This is the size that covers the widest share of all-round boards: recreational paddlers on 9 ft to 10 ft 6 shapes, hire fleets running mixed sizes, and shops that want one ankle leash doing most of the work on the wall. It sits naturally beside the 8 ft and 12 ft models, which use the same cuff pattern and hardware.

- All-round reach — a 10ft sup leash gives a 9 ft to 10 ft 6 board room to spin in whitewater without the cord coming tight at your ankle. - Ankle-cuff fit — the sup ankle leash closes low with a hook-and-loop strap, so it goes on over a bare ankle or a thin neoprene sock without help. - Padded pressure relief — neoprene padding under the strap spreads the pull across the ankle instead of cutting in at one point. - Swivels at both ends — stainless swivel joints let the cord rotate, which is what stops it winding into a twisted rope that drags and tugs. - Rail protection — the webbing rail saver takes the wear at the board end, so the cord pulls against the saver rather than against the rail. - String included — the leash string is fitted and ready to thread through the leash plug, so the leash goes onto the board straight away. - One sup leash supplier for the family — the 8 ft, 10 ft and 12 ft ankle models share the cuff pattern and hardware, so a shop's wholesale sup leash range comes from a single line instead of three separate purchases.

Ankle Cuff and Hardware

The cuff is the part a rider notices first, so it is worth knowing how it fits. The ankle cuff is padded and closes with a hook-and-loop strap, which lets you set it once and repeat the same closure every session. Close it so the padding sits flat against the skin and the strap overlaps by a comfortable margin — tight enough that the cuff cannot slide around the ankle, loose enough that you can still feel your foot warm up after ten minutes on the water. A paddleboard ankle leash strapped too tight is worse than one that is slightly loose, because the pressure point shows up long before the session ends.

Worn over a thin neoprene sock or a low boot, the same strap adjustment usually covers it. If you paddle in thick winter boots, check the cuff opening against your footwear before you commit to a size.

The swivels do the quiet work. One at the cuff end and one at the board end let the cord rotate instead of winding up, which is what stops a leash from becoming a twisted rope that drags behind you. Turn each swivel by hand when the leash is new; it should move freely and sit flush against its housing.

At the board end, the rail saver is a webbing strap that spreads the pull across a wider area than the string alone and keeps the cord off the rail. The string runs through the leash plug and the saver, and it should still be able to slide a little rather than sitting locked solid.

Selecting Length and Cuff

1. Start from the board, not the number. An all-round board around 9 ft to 10 ft 6 sits comfortably on this 10 ft model; drop to the 8 ft version for shorter, lighter boards, and step up to 12 ft when the board is long, wide or used for touring.
2. Decide ankle or knee. The ankle cuff goes on faster and suits riders who stay on their feet; knee cuffs sit higher on the leg and are the usual choice on very large boards or where the rider kneels a lot.
3. Match the leash to the hardest day, not the average one. A sup safety leash used in the surf zone takes repeated shock loads that a flat-water leash never sees, so choose cord and hardware for the worst conditions the board will meet.
4. Check the connection point on the board. The rail saver should sit flat against the rail with the string through the leash plug, clear of the handle and any deck rigging.
5. Build the run if you are buying for a shop.

Complete Accessory Range

Specifications

Care and Storage

• Rinse with fresh water after every saltwater session — sand and salt collected in the cuff and swivels are what wear them out first.
• Dry the 8 mm sup leash loose and out of direct sun; hanging it over a rail in the shade lets the cord relax instead of drying into a coil.
• Do not leave it wound tight around a paddle or stored in a hot car for weeks — heat and a permanent set are what make a cord feel stiff.
• Check the string before you launch. On any sup safety leash the string is the cheapest, fastest-wearing part, and it is the one that lets go first.
• Look at the cord for nicks, flat spots and whitening, and turn the swivels by hand — a swivel that no longer spins means the leash is near the end of its working life.
• Rinse the cuff padding and let it dry fully before storage so the neoprene does not sit damp between sessions.
• Keep it away from solvents, sunscreen overspray and fuel; the strap and cord pick up damage from things that never touch the water.

Ordering and Delivery

1. Send the model list with lengths, cuff styles and quantities so the quotation matches what you actually need.
2. Confirm the build on the exact code you are ordering — the 8 mm sup leash cord, the cuff style, the swivels and the string should match the sample you approved.
3. Tell us the branding and packing you want on the wholesale sup leash order — logo, label and carton marks — so they are quoted from the start rather than added later.
4. Ask your sales contact to confirm current lead time, shipping terms and payment terms for your destination.
5. Agree how samples are handled before bulk production, and keep the approved sample as the reference for the first shipment.
6. Keep the specification on file with us. As a sup leash supplier we hold approved details against your account, so a repeat order matches the first one.

Scale & Supply Capability

CIMI is a factory-based supplier with 16 years in surf and watersports hardgoods, manufacturing at our own facility rather than sourcing through traders. Chain stores, supermarkets and surf-brand stores buy from us because one supplier covers a full accessory assortment, so a season's order and its reorders can be planned together. We take on OEM and private-label work, adapting designs, colourways and branding to your programme, and we schedule production against your agreed range plan. Send us your buy list and target dates, and we will confirm what we can make and when.

FAQ