L22607 SURF LEASH REGULAR 10FT 8MM

Product Overview

The L22607 is the 10 ft / 8 mm model in CIMI's regular leash range: a single-cord ankle leash for medium surf on boards that sit a long way from the rider. Three metres of cord lets a paddleboard or a longboard drift and roll before the leash comes tight, and the 8 mm (5/16 in) cord is the heavier option in the regular family, so it holds its shape when a set stands up on the inside section. Fit a 10ft surfboard leash like this to a bigger hybrid, a long log or a soft-top and the extra cord body is the first thing you notice in the water. At the ankle, a double-padded neoprene cuff spreads the pull across a wider band of skin; at the board end, a 38 mm rail saver keeps the cord clear of the rail when the leash is fully stretched. Both joints turn on 316 stainless steel swivels, so the cord follows the board instead of winding itself into a coil while you paddle. Every part is sized for a longer board: more cord, a wider rail saver and a swivel set with material to spare. It is the single entry that covers both SUP and longboard customers on an accessory wall, and for a wholesale surf leash programme or a custom surf leash order it is a straightforward build to brand and repeat.

Key Features

• Double-padded neoprene ankle cuff. Two layers of neoprene sit between the webbing and your skin, spreading the pull over a wider band instead of cutting into one spot. On a longboard surf leash of this length the cuff stays loaded for longer, and that padding is what keeps a bare ankle comfortable deep into a session.
• 8 mm (5/16 in) TPU cord. This 8 mm sup surf leash runs a thicker cord than the 7 mm regular models, and the extra wall thickness is what resists stretching when a heavier board keeps pulling. TPU gives before it shocks, so the rail takes a steady load rather than one hard jolt.
• 38 mm rail saver. The webbing at the board end is wide enough to spread that load along a section of rail rather than a single point, which matters most on the thicker rails of a SUP or a log.
• 316 stainless steel swivels. Two rotation points in marine-grade stainless let the cord turn with the board and release twist before it builds into a coil.
• Streamlined hardware. The moulded connector and the low-profile cuff keep the metalwork close to the ankle and the rail, so there is less to catch when you remount after a wipeout.
• Cuff strap that closes flat. Woven webbing wraps through the buckle and back over itself, holding the surfboard ankle leash tight without a loose tail flapping in the water.

Material & Build

Those shares describe the whole assembly rather than one component: the TPU is the cord, polypropylene and nylon go into the webbing and stitching, neoprene forms the cuff, and the stainless content is the swivel hardware. The cord is top-grade TPU, supplied as one continuous length with a smooth surface that sheds water and dries quickly. The cuff is doubled neoprene, and the webbing strap is stitched through the outer layer so the working load runs through the strap rather than the foam. At the board end, the rail saver carries the cord away from the rail, and the moulded connector holds the swivel square so it turns instead of twisting the cord. As a surf leash manufacturer, we have supplied surf hardware since 2007, and the leashes that leave our factory for a wholesale surf leash programme are built to the same specification as the ones that go out under customer brands. Cord colour, cuff branding and packaging are what change from order to order.

Dimensions & Board Fit

• 10 ft / 3 m of cord. At rest the leash is longer than most riders expect, and it stretches further under load, so a board that spins in whitewater still has room before the cord goes bar tight.
• 8 mm / 5/16 in thickness. On a 10ft surfboard leash that extra mass is working material rather than dead weight: it resists stretch and stops a heavy board running to the end of the cord in a single pull.
• 38 mm rail saver. Check the widest point of the rail where the saver will sit. The 38 mm webbing is designed to clear a thick longboard or SUP rail; on a narrow performance shortboard it is more saver than the rail needs.
• Matching length to board. Many shops work to roughly one foot of leash per foot of board, which puts this model at the top of that scale: a 9 to 10 ft log, a longer paddleboard or a big hybrid.
• Where the extra thickness earns its place. A longboard surf leash on a heavier board will thin and fatigue faster in 7 mm; the 8 mm cord keeps more reserve for the days when the surf is bigger than forecast.
• What to check before ordering. Measure from the rail plug to the ankle, look at the curve of the rail, and confirm the leash string attachment point is sound. If your boards run beyond 10 ft, tell us before you commit.

Boards & Conditions

Medium waves are the working range here, and that shapes who the leash suits. On a stand-up paddleboard, 10 ft of cord gives you room to step back, pivot and fall without the board snapping at your ankle. The specification calls this a regular SUP ankle leash for medium waves, which is exactly the brief it was built to, and paddlers who surf their board rather than cruise will find it works as a sup surf leash without the bulk of a knee-cuff model. Hybrids, mid-lengths and larger soft-tops sit comfortably in the same range. Conditions matter as much as the board. This is a longboard surf leash for clean-to-choppy medium surf, the kind of day where the set wave is around head high on the face and the inside is mostly whitewater. Push it into proper big-wave sessions and you are asking a regular leash to do a job it was not designed for. Flat-water paddlers still get value from the length. A 10ft surfboard leash keeps the board within reach when the wind takes it on a lake or an estuary, and the padded cuff stays comfortable through a long, slow session. Shops with rental racks tend to keep one 10 ft ankle leash on the wall because a single size covers most of the boards in the store.

Specifications

Use & Care

1. Check the cord before you paddle out. Run the whole length of the 8 mm surf leash through your hands and look for nicks, cloudy patches or a flattened section. Any of those means the cord is on its way out.
2. Inspect the cuff and the stitching. Look for frayed webbing, a worn strap edge or stitching that has started to pull out of the neoprene.
3. Turn both swivels. They should rotate freely by hand. A swivel that feels gritty or stiff needs a fresh-water rinse and a second check before the leash goes back in the water.
4. Rinse after every salt-water session. Fresh water on the cord, the swivels and the rail saver takes the salt off before it dries into the moving parts.
5. Dry in the shade and store it loose. Hang the surfboard ankle leash or coil it in wide loops rather than a tight figure-eight, and keep it off hot concrete and out of direct sun for long periods.
6. Retire it at the first sign of wear. A leash is a wear item; a cord that has lost its surface or a rail saver that has frayed is a leash to replace, not to repair.
7. Use it for surfing only. This is not a tow line, an anchor or a tie-down, and it should not be used for towing a board or a rider.

Ordering & Delivery

1. Send the model and the quantity. Give us the length, cord thickness and cuff style you want, and tell us whether the order repeats last season's mix or adds a new size.
2. Confirm the colourway. Cord colour, cuff colour and rail saver colour are agreed before production starts, and a physical colour reference is the safest way to lock them.
3. Decide the branding. For a custom surf leash we can print the cuff, add a header card and pack in a sleeve or polybag; send artwork with the order so it can be checked against the cuff shape.
4. Agree the schedule. Production slots and shipping dates are quoted for your order and confirmed in writing once the specification is locked.
5. Confirm the commercial terms. Minimum order quantity, price, payment terms and freight are quoted per order; as a surf leash manufacturer we quote against your actual mix rather than a catalogue figure, so ask your sales contact to confirm the numbers for your quantities.
6. Ask about samples. If you need to feel the cord and the cuff before committing, ask your sales contact about sample availability and current terms.
7. - Leashes. This model sits in the regular group alongside hypalon, non-slip, coil, SUP knee and SUP ankle builds from 5 ft to 12 ft, so a store can fill a leash wall from one supplier on a single wholesale surf leash order. - Fins. Honeycomb, timber, G10 glass and nylon fins with single-tab and double-tab options, plus fin accessories, so the same buy covers the board's underside as well as its edge. - Traction. Tail pads, centre pads, skimboard pads and waxless pads give a shop the grip category without a second vendor. - Covers. Basic bags, regular bags, stretch covers and bodyboard bags protect the boards the leashes are sold with. - Racks. Travel rax with tie-downs, storage racks, display racks, bike racks and wax inserts for the shop floor and the customer's garage. - Building a set. If you want a custom surf leash matched to your covers and pads, with the same cord colour and the same header card, say so when you send the buy list.

Scale & Supply Capability

CIMI is a factory-based supplier with 16 years in surf and watersports hardgoods, manufacturing at our own facility rather than sourcing through traders. Chain stores, supermarkets and surf-brand stores buy from us because one supplier covers a full accessory assortment, so a season's order and its reorders can be planned together. We take on OEM and private-label work, adapting designs, colourways and branding to your programme, and we schedule production against your agreed range plan. Send us your buy list and target dates, and we will confirm what we can make and when.

FAQ