• T27048 SURF TRACTION TAIL PADS
  • T27048 SURF TRACTION TAIL PADS

T27048 SURF TRACTION TAIL PADS

No.T27048
PIECES: 3 PATTERN: DIAMOND ADHESIVE: 3M
  • T27048 SURF TRACTION TAIL PADS

Description

Product Overview

The T27048 surf traction pad is a three-piece tail set — one centre piece and two side pieces — embossed with a diamond pattern and backed with 3M adhesive. It arrives as a set of three, and that matters more than it sounds: a single-piece pad has to be cut down to suit the tail, while three pieces can be spaced to the width of the board before anything is peeled. A surfboard tail pad sits exactly where the back foot pivots, so the shape of the set has to match the shape of the tail. Run the pieces tight together on a narrow squash tail, or open the gaps on a wider thumb or bat tail to cover more deck without overhanging the rail. The diamond relief gives the back foot an edge to push against through a turn, and the 3M backing means the pad goes onto a finished board without glassing work. Rental fleets and surf schools buy this way too: a surfing traction pad that is bonded rather than glassed on can be replaced at the end of a busy season without sending the board to a workshop, and the three-piece layout can be re-spaced if a repair patch changes the deck.

Material, Pattern & Adhesive

  • Embossed, not printed. The diamond pattern is pressed into the sheet itself, so grip comes from the relief rather than from a sprayed-on grit that wears smooth. On a surf traction pad that is waxed, ridden and rinsed every week, that is the difference between texture that stays and a coating that disappears.
  • Grooves that clear water. The channels between the diamonds give water a path out from under the back foot and give wax somewhere to sit instead of smearing flat. On a surfboard traction pad working in a school or rental fleet, that drainage is what keeps the deck usable session after session.
  • Easy to replace when a fleet turns over. Because the set is bonded rather than glassed in, an operator can swap a worn pad between seasons without touching the glass — this is the traction pad surf schools keep on the shelf for exactly that job.
  • A low, honest profile. One flat layer of sheet means the pad sits close to the deck and keeps the feel of the board under your back foot instead of adding a soft step. Choosing a traction pad for surfboard use usually comes down to that: how much the pad changes contact with the deck.
  • 3M adhesive backing. The pad comes with 3M pressure-sensitive adhesive and a peel-off liner, so it bonds at room temperature with no resin, no mixing and no clamps. That keeps a fitting clean next to a customer's finished board.
  • Pattern depth stays consistent. Because the relief is embossed into the sheet rather than added piece by piece, the centre and side pieces carry the same depth, so a set on display reads as one design rather than three offcuts.
  • Colour-blocked face. The set shown in our photography runs black, light blue and pale yellow in a checkerboard layout with a matte skin that hides wax haze and shelf scuffs. It gives the tail a graphic look without needing a printed layer on top of the grip.

Fitting & Installation

  1. Measure the tail before anything else. Run a tape across the deck where the back foot lands and compare that width with the footprint of the three pieces — a surfboard tail pad has to cover the stance zone without running past the rail line, and this is the quickest way to see whether the set sits comfortably.
  2. Dry-fit the set with the liner still on. Put the three pieces where they will go, line the centre piece up with the stringer and check that the side pieces clear the leash plug; a longboard traction pad needs the side pieces spaced wider so the extra tail width is covered.
  3. Strip the deck. Take off all the wax and residue from the area the pad will cover, then wipe the surface dry. The adhesive holds on a clean, dry deck and lifts at the corners on a waxy one.
  4. Tape your lines. A strip of masking tape along each side of where the centre piece goes keeps it square while you work and gives you an edge to press against.
  5. Peel and press in stages. Lift a few centimetres of liner at the nose end of a piece, align it to the tape, then peel the rest away while pressing the pad down from the middle outward with your thumbs.
  6. Check the edges and let it settle. Press the whole perimeter again once the piece is down, then keep the board out of the water until the adhesive has fully wet out. The traction pad surf schools fit across a fleet goes on the same way, just repeated board after board.

Use & Care

Day to day, a surfing traction pad asks very little: rinse it with fresh water after salt-water sessions, let it dry out of direct sun, and brush off sand before it works into the grooves. A soft brush and mild soap are enough — solvent-based cleaners can attack the adhesive at the edges and dull the embossed face.

Wax is the usual problem. Wax settles in the diamonds and, left to build up, fills the relief until the deck feels like a plain sheet. Scrape the worst of it off with a plastic scraper, then work a soft brush across the pattern; a surfboard traction pad cleaned this way keeps its texture far longer than one scrubbed with an abrasive pad.

Heat is the other thing to watch. A board left in a closed car or leaning against a hot wall can soften the adhesive and lift an edge, and once an edge lifts, sand and salt get underneath. A longboard traction pad stored the same careless way behaves exactly the same, so keep boards shaded and check the perimeter before each trip.

Matching Accessories

  • Leashes. Hypalon leashes in 6 ft, 7 ft, 8 ft and 9 ft cover shortboards through to longboards, and because we are one of the surf board manufacturers producing both the traction pad and the leash, they can be packed into a single order.
  • Fins. Honeycomb fins with single-tab or double-tab bases are sized by rider weight, so a board can leave the shop with its fin set and its tail pad chosen in the same conversation.
  • Traction range. If this set is the surfboard traction pad your range is missing at the tail, the rest of the deck can be covered with centre pads, waxless deck pads or a skimboard pad from the same family.
  • Covers. Basic bags, regular bags and stretch covers take the boards these pads go on, which makes a bag-and-pad bundle an easy seasonal add-on.
  • Racks. Travel rax and tie-downs, storage racks, display racks and bike racks get boards off the floor and facing the customer.

Specifications

SpecificationDetail
ModelT27048
Product typeSurf traction tail pad
Set contents3 pieces per set
PatternDiamond
SurfaceEmbossed diamond relief
FinishMatte
Adhesive3M pressure-sensitive with peel-off liner
ConstructionSingle-layer sheet
PlacementSurfboard tail deck
Board typesShortboard, hybrid and longboard tails
Piece layoutOne centre piece and two side pieces
Fitting methodPeel-and-stick, no glassing required

Ordering & Delivery

  1. Send the codes and quantities in one list, including any other traction pad surf shops or schools on your account are restocking, so the whole lot can be planned as one production run.
  2. Confirm the specification for your market. Pattern, face design and packing are set per code, so if you are buying a traction pad for surfboard ranges sold under your own label, tell us what the carton and any hangtag need to say before production starts.
  3. Ask about sample availability and current lead time. Both move through the season, so your sales contact can confirm what is possible for the surf traction pad quantities you have in mind.
  4. Agree packing and terms in writing. Carton quantities, labelling, payment terms and shipping arrangements are confirmed on the order, and they are worth settling before the busy season rather than during it.
  5. Plan the reorder with the first order. We keep the pattern and adhesive specification for each code on file, so a second batch is produced to the same reference you approved.

Scale & Supply Capability

CIMI is a factory-based supplier with 16 years in surf and watersports hardgoods, manufacturing at our own facility rather than sourcing through traders. Chain stores, supermarkets and surf-brand stores buy from us because one supplier covers a full accessory assortment, so a season's order and its reorders can be planned together. We take on OEM and private-label work, adapting designs, colourways and branding to your programme, and we schedule production against your agreed range plan. Send us your buy list and target dates, and we will confirm what we can make and when.

FAQ

Will this surfboard tail pad fit a wide thumb tail?

Measure across the deck where the back foot lands and compare it with the footprint of the three pieces. A wide thumb or bat tail usually has room to open the gaps between the centre and side pieces so the pad covers more deck; on a narrow squash tail the pieces sit tight together. If the tail is unusually wide or narrow, send us the measurement and we will tell you whether this set covers it or whether a centre pad is needed as well.

How well does the 3M adhesive stay down?

The backing is 3M pressure-sensitive adhesive applied at room temperature — no resin, no clamps. Where a pad fails it is almost always at the edge and almost always because something was left underneath: wax, sand or a damp deck. Press the whole perimeter again the day after fitting and keep the board out of the water until the adhesive has fully wet out, and the edges stay down.

Can the pad be trimmed to fit a narrower tail?

Yes. Trimming the outside edge of the side pieces is normal practice when a tail is narrower than the set. Cut from the edge that runs along the rail rather than the edge that meets the centre piece, so the three pieces still line up. When you are choosing a traction pad for surfboard tails of different widths, keeping the centre section intact is what preserves the look of the set.

Does the diamond pattern actually add grip, or is it cosmetic?

It adds grip, for two reasons. The relief gives the back foot an edge to push against, and the grooves between the diamonds let water and wax move instead of sitting under the foot. A surfing traction pad with a flat face still works, but it tends to feel slicker once the deck is wet and freshly waxed.

Can this set go on a longboard?

It can, and the three-piece layout is the reason. A longboard traction pad needs coverage further forward across a wide tail, so the side pieces get spaced wider apart and the set sits lower on the deck. On a very wide longboard tail, pair the set with a centre pad to cover the rest of the stance area.

What is in the pack, and what do I need to fit it?

Three pieces — one centre section and two side pieces — with the 3M adhesive already applied and a peel-off liner on each. You will need a way to strip wax, a clean cloth, masking tape for your guide lines and something to press the edges down with. No resin or special tools are required beyond that.

Leash

Fins

Traction

Cover

Rack

Regular longboard ankle leash for medium to large waves or a longer board
The CIMI Surf Leash Hypalon 8ft 7mm is the ideal choice for surfers seeking a durable and reliable leash. Made with high-quality Hypalon, this leash offers exceptional strength and comfort, ensuring a safe and enjoyable surfing experience.
Regular leash for medium-sized waves and all-around conditions
Lightweight leash for small to medium-sized waves
Honeycomb fins are made using a resin transfer molding process. This versatile fin material is light, and can be used in a variety of different conditions
Honeycomb fins are made using a resin transfer molding process. This versatile fin material is light, and can be used in a variety of different conditions
The CIMI Double Tab Surf Fins are crafted to boost your surfing performance. With high-quality construction and superior design, these fins offer enhanced stability, control, and durability.
Honeycomb fins are made using a resin transfer molding process. This versatile fin material is light, and can be used in a variety of different conditions
Enhance your surfing experience with CIMI's high-performance Surf Traction Tail Pads. Designed for durability and superior grip, these tail pads provide exceptional control on your surfboard.
Your product's brief description
Your product's brief description
Your product's brief description
Your product's brief description
Your product's brief description
Your product's brief description
Your product's brief description
Your product's brief description