• T00346 SURF TRACTION TAIL PADS
  • T00346 SURF TRACTION TAIL PADS
  • T00346 SURF TRACTION TAIL PADS
  • T00346 SURF TRACTION TAIL PADS

T00346 SURF TRACTION TAIL PADS

No.T00346
PIECES: 3 PATTERN: DIAMOND ADHESIVE: 3M
  • T00346 SURF TRACTION TAIL PADS
  • T00346 SURF TRACTION TAIL PADS

Description

Product Overview

This three-piece surf traction pad is built for the tail of a surfboard deck, with a diamond pattern across all three panels and a 3M adhesive backing. It goes on with a clean, dry deck and a firm press — no resin, no contact glue, no workshop time.

What it does is simple. It gives the back foot an edge to push against when the board comes off the bottom or goes into a turn, and it puts a layer between the rider and the glass exactly where heels and knees land hardest. Riders fit it when a pad has gone smooth or started lifting at a corner. Shops, surf schools and board builders fit it to new boards before they leave the workshop, because a finished tail is one less thing for the customer to do before the board goes in the water.

The set is three pieces rather than one wide sheet, so the panels can be positioned to the tail's outline instead of being forced over it — which is also why a worn panel can be dealt with on its own without touching the rest of the set.

Three-Piece Layout

  • Gap control — the gap between the pieces is the adjustment: wider on a square tail, tighter on a pin tail, and symmetrical on both sides of the stringer.
  • Centred on the stringer — the middle piece lines up with the stringer and the outer pieces mirror it, which is what keeps the set looking straight from the water and from the shop floor.
  • Pattern alignment — the diamond runs the same direction on all three pieces, so the surfing traction pad reads as one surface rather than three separate offcuts.
  • Surfboard tail pad footprint — the set covers the standing area behind the back foot; riders who stand right over the plug usually push the pieces back to the very end of the tail.
  • Longboard traction pad placement — on a longer board the same three pieces can sit further forward or further back, following where the rider actually stands when trimming rather than a fixed position.
  • Even margins — matching the gap on both sides of the stringer is the difference between a pad that looks factory-fitted and one that looks hurried.
  • Edge line — the outer pieces should finish inside the rail, so the pad edge never sits where a hand goes when the board is carried under the arm.

Fitting Guide

  1. Fit on a dry, mild day in a clean workspace. The adhesive bonds most reliably to a dry deck at normal room temperature, so keep the board out of direct sun and out of the cold, and do not plan a session straight afterwards.
  2. Strip the old pad or wax from the tail and wipe the area until the deck is clean and dull. A traction pad for surfboard fitting should go straight onto bare glass — wax film, sunscreen and mould-release residue are the usual reasons a pad lifts at a corner.
  3. Dry-fit the three pieces of this surfboard traction pad before you peel anything. Set the middle piece on the stringer, space the outer pieces evenly and check the gaps by eye; this is the only step you cannot undo cleanly.
  4. Mark the outline with tape or a soft pencil line if you want a reference, then peel a few centimetres of backing, set the piece on the mark and work the rest of the backing away as you press down.
  5. Press from the centre outwards with the flat of your hand, working along the diamond pattern, then go over the border once more — the edge is what lifts first.
  6. If a surf front traction pad is going on in the same session, fit the tail set first and work forward, so the stance is settled before the front section goes down.
  7. Leave the board out of the water for a while after fitting. A pad pressed on and surfed within the hour is the one that comes back with lifted corners.

Matching Accessories

  • Leashes — regular, non-slip, Hypalon and SUP leashes in the lengths that match the board; the tail and the leash plug share the same end of the deck, so both are usually fitted in one go.
  • Fins — honeycomb, timber, G10 glass and nylon sets across single tab, double tab and box formats, so a board can leave the workshop finished rather than half-built.
  • Traction — centre pads and waxless panels continue the grip forward from the tail set; a surf front traction pad is the usual next item on a shortboard, and the diamond pattern carries up the deck.
  • Covers — basic bags, regular bags and stretch covers sized to the board, for storage between sessions and for shipping a finished board out to a customer.
  • Racks — travel rax and tie-downs, storage racks, display racks and bike racks, which is where a shop's stock tends to end up between deliveries.
  • Replacement work — for shops that do a steady trade in repairs, keeping a traction pad for surfboard replacement jobs in stock means a damaged tail can be matched without ordering a full new range.
  • One pattern across a range — buying the tail pad alongside the rest of the deck hardware keeps the pattern language consistent across a board and across a season's range.

Care & Removal

  1. Rinse after every session. Salt and sand work into the texture of a surfing traction pad, and a quick freshwater rinse keeps the surface from going slick.
  2. Wash with mild soap and a soft brush, then rinse again. Keep solvents, acetone and harsh cleaners away — they attack the adhesive line along the edge long before they do anything useful to the surface.
  3. Check the surface every few weeks. Once a surf traction pad has gone smooth and shiny across the middle, the diamond has worn down and it is time to replace it.
  4. Deal with a lifted corner early. Warm it gently, press it back down and leave the board overnight with a weight on the pad; a corner left flapping takes sand under the adhesive and will not sit flat again.
  5. Remove a pad only when you mean to replace it. Warm the surface on a low setting, slide a thin blunt blade under one corner and work along slowly — pulling cold is what lifts glass along with the foam.
  6. Store boards pad-up and out of direct sun. A longboard traction pad left flat against a hot car roof or folded into a bag in summer will soften at the edge long before it wears out.

Specifications

Product typeSurf traction pad, tail section
Set typeThree-piece surfboard traction pad
Board fitSurfboard tail pad and longboard traction pad, shaped to the tail outline
ModelT00346
Pieces per set3
PatternDiamond
Adhesive3M pressure-sensitive adhesive
Deck positionTail, behind the back foot
Panel layoutOne centre panel with two mirrored outer panels
Board typesShortboard, funboard and longboard tails
Storage before fittingKeep the panels flat, out of direct sun and away from heat sources until the deck is ready

Ordering & Confirmation

Commercial details are confirmed per order rather than fixed on this product, because they move with the design, the packing and the season. Tell us the pattern and colour direction you need, whether the pads should arrive as loose sets for workshop fitting or bagged and labelled for shelf display, how the range splits between tail pads and the rest of the deck, and the date you need stock in store.

We work with surf board manufacturers and store chains on private-label runs, developing the pad from your artwork with a sample approved before bulk production starts. Ask your sales contact about sample availability, current lead times and the quantity breaks that apply to your order — settling those early is what keeps a pre-season delivery on schedule.

If you are matching a pad that is already fitted to a board you sell, send the piece or a tracing so the outline and spacing come from the original rather than an approximation.

Scale & Supply Capability

CIMI is a factory-based supplier with 16 years in surf and watersports hardgoods, manufacturing at our own facility rather than sourcing through traders. Chain stores, supermarkets and surf-brand stores buy from us because one supplier covers a full accessory assortment, so a season's order and its reorders can be planned together. We take on OEM and private-label work, adapting designs, colourways and branding to your programme, and we schedule production against your agreed range plan. Send us your buy list and target dates, and we will confirm what we can make and when.

FAQ

Will this three-piece set fit my board's tail?

A three-piece set is more forgiving than a single panel, because the gaps between the pieces absorb the difference between a wide, square tail and a pin tail. Line the middle piece up on the stringer and let the outer pieces follow the rail line, keeping them inside it. Check the width of the tail where your back foot lands before you commit; if the outline is unusual, send us a tracing and we will confirm the spacing. A surfboard tail pad looks right when the outside pieces finish inside the rail, not on it.

What does the diamond pattern actually do?

The diamond is a working texture rather than decoration. It gives the ball and heel of the back foot an edge to push against in every direction — sideways into a cutback, forward for drive off the bottom — and because the pattern is raised, it stays readable as it wears, so you can see when the surface has gone smooth. All three pieces of this surfboard traction pad run the diamond in the same direction, so the feel is the same whichever part of the pad the foot lands on.

Can I fit it over an old pad or leftover wax?

No. The adhesive needs bare, clean glass to bond. Wax, old adhesive, sunscreen and mould-release residue all sit between the pad and the deck, and a traction pad for surfboard use that goes on over a film of wax will lift at a corner within a session or two. Strip the old pad, wipe the tail until the deck is dull and dry, and only then peel the backing.

Does it work on a longboard or a soft-top?

On a longboard it works well, because the three pieces let you place the set where you actually stand rather than at a fixed distance from the tail. Soft-tops are a different matter: the deck is a soft foam skin rather than glass, and pressure-sensitive adhesive does not bond to it the same way. Tell us the board type when you enquire and we will confirm whether the pad suits that deck.

Can I trim the pieces to fit a narrow tail?

Yes, but only from the outside edge. Take material off the piece that faces the rail, keep the diamond pattern and the sealed border intact, and remove a little at a time — a surfing traction pad cut through the middle of the pattern loses both the look and the edge seal. On a very narrow tail it is usually better to close the gaps between the three pieces than to cut them down.

Is there a matching front pad for the rest of the deck?

The tail set covers the standing area behind the back foot. If you want grip further forward, a surf front traction pad or a centre pad carries the same diamond pattern up the deck, and the two can be fitted as a set. On a shortboard most riders stop at the tail; on a longboard or a wider board the extra coverage is worth having.

Leash

Fins

Traction

Cover

Rack

Regular longboard ankle leash for medium to large waves or a longer board
The CIMI Surf Leash Hypalon 8ft 7mm is the ideal choice for surfers seeking a durable and reliable leash. Made with high-quality Hypalon, this leash offers exceptional strength and comfort, ensuring a safe and enjoyable surfing experience.
Regular leash for medium-sized waves and all-around conditions
Lightweight leash for small to medium-sized waves
Honeycomb fins are made using a resin transfer molding process. This versatile fin material is light, and can be used in a variety of different conditions
Honeycomb fins are made using a resin transfer molding process. This versatile fin material is light, and can be used in a variety of different conditions
The CIMI Double Tab Surf Fins are crafted to boost your surfing performance. With high-quality construction and superior design, these fins offer enhanced stability, control, and durability.
Honeycomb fins are made using a resin transfer molding process. This versatile fin material is light, and can be used in a variety of different conditions
Enhance your surfing experience with CIMI's high-performance Surf Traction Tail Pads. Designed for durability and superior grip, these tail pads provide exceptional control on your surfboard.
Your product's brief description
Your product's brief description
Your product's brief description
Your product's brief description
Your product's brief description
Your product's brief description
Your product's brief description
Your product's brief description